LEARNING THE BASICS OF INSTALLING A BATHTUB

Learning the Basics of Installing a Bathtub

Learning the Basics of Installing a Bathtub

Blog Article

Call Today

Right here down the page you might get more helpful resources concerning How to Install a Bathtub Yourself.


How to Install a Bathtub
Installing a bath tub isn't specifically brain surgery, but it does call for strong plumbing, carpentry, and occasionally, tiling skills. Replacing an old bath tub with a brand-new one is also a reasonably tough project. If the old bathtub is readily accessible, the job can move speedily; if you need to open up a wall to eliminate the old tub as well as position the new bath tub, the job is much harder. In either situation, the job is within a residence handyman's abilities, although you will need an assistant to vacate the old tub as well as embeded in the brand-new one. See to it you have actually qualified on your own for the task and also are comfortable attempting it. Instead of employing a professional to take over a halfway-completed task, it is much better to take into consideration utilizing one prior to you start. Opportunities are you might require a specialist plumber to make tube links.
This post will help you install a new bath tub in your bathroom if you have actually currently bought a brand-new tub and do not require to change the arrangement of your previous water pipelines.
Your tools and also material list must make up the following:
  • New Bath tub
  • Hammer

  • Pipe Wrenches

  • Prybar

  • Safety Glasses

  • Degree

  • Pliers

  • Adjustable Wrench

  • Putty Blade

  • Screwdriver

  • Cold Blade

  • Measuring tape

  • Pipe Caps


  • Planning for the Installation


    To start with, the sustaining frame supplied with the bathroom should be fitted (if needed) according to the supplier's instructions. Next, fit the taps or mixer to the tub. When fitting the faucet block, it is necessary to make certain that if the faucet features a plastic washer, it is fitted between the bath as well as the faucets. On a plastic bath, it is also practical to fit a supporting plate under the taps system to avoid stress on the tub.
    Fit the versatile faucet adapters to the bottom of both taps using 2 nuts and olives (in some cases supplied with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet opening, and then pass the electrical outlet via the hole in the bathroom. Utilize the nut provided by the supplier to fit the plug-hole. Take a look at the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
    Next off, fit completion of the flexible overflow pipeline to the overflow electrical outlet. Afterwards, screw the pipe to the overflow face which must be fitted inside the bath. Ensure you make use of all of the supplied washers.
    Link the catch to the bottom of the waste electrical outlet on the bath tub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, and also screw on the catch to the electrical outlet. Link the bottom of the overflow tube in a similar manner.The bath ought to now be ready to be suited its last placement.

    Removing Old Touches


    If you require to change old taps with new ones as a part of your installation, after that the first thing you need to do is disconnect the supply of water. After doing so, turn on the faucets to drain pipes any kind of water continuing to be in the system. The procedure of removing the existing faucets can be quite bothersome as a result of the restricted access that is commonly the situation.
    Use a container wrench (crowsfoot spanner) or a tap device to reverse the nut that links the supply pipes to the faucets. Have a cloth all set for the remaining water that will certainly originate from the pipelines. When the supply pipelines have been eliminated, make use of the exact same device to loosen the nut that holds the taps onto the bath/basin. You will need to quit the solitary taps from turning throughout this procedure. Once the taps have actually been gotten rid of, the holes in the bath/basin will certainly need to be cleansed of any old sealing compound.
    Prior to going on to fit the new taps, compare the pipe connections on the old taps to the new faucets. If the old taps are longer than the brand-new taps, then a shank adapter is required for the new faucets to fit.

    Installing the Bath tub


    Utilizing both wooden boards under its feet, place the bathtub in the needed position. The wooden boards are valuable in uniformly spreading the weight of the bathtub over the location of the boards as opposed to concentrating all the weight onto four small points.
    The following objective is to make sure that the tub is leveled all round. This can be achieved by examining the spirit level and also changing the feet on the bathtub till the level reads degree.
    To set up taps, fit all-time low of the furthest versatile tap adapter to the appropriate supply pipeline by making a compression join; then do the exact same for the other faucet.
    Switch on the water supply and inspect all joints and new pipework for leakages and tighten them if essential. Fill the tub as well as also inspect the overflow outlet and also the normal outlet for leakages.
    Ultimately, fix the bath paneling as defined in the supplier's instruction manual. Tiling as well as securing around the tub ought to wait up until the tub has been utilized at the very least when as this will settle it into its last position.

    Fitting New Taps


    If the tails of the new taps are plastic, then you will require a plastic adapter to stop damages to the string. One end of the port fits on the plastic tail of the tap as well as the other end offers a connection to the existent supply pipes.
    If you need to fit a monobloc, then you will certainly require reducing couplers, which attaches the 10mm pipeline of the monobloc to the typical 15mm supply pipeline.
    Next, place the tap in the placing opening in the bath/basin guaranteeing that the washers remain in location in between the faucet and the sink. Safeguard the faucet in place with the supplier supplied backnut. Once the faucet is securely in position, the supply pipelines can be linked to the tails of the faucets. The faucets can either be connected by utilizing corrugated copper piping or with normal tap adapters. The former type needs to be connected to the faucet finishes initially, tightening up only by hand. The supply pipelines can later on be linked to the various other end. Tighten both ends with a spanner after both ends have actually been attached.

    Tiling Around the Bathtub


    In the area where the bath meets the tile, it is necessary to secure the joins with a silicone rubber caulking. This is necessary as the installation can relocate sufficient to crack a rigid seal, causing the water to permeate the wall between the bath and the tiling, resulting in problems with dampness and possible leakages to the ceiling below.
    You can choose from a selection of coloured sealers to blend in your fixtures and also installations. They are offered in tubes and cartridges, and also are capable of securing spaces as much as a width of 3mm (1/8 inch). If you have a bigger space to fill, you can load it with twists of drenched newspaper or soft rope. Remember to constantly fill up the bathtub with water before securing, to allow for the activity experienced when the tub is in usage. The sealant can split fairly early if you do not take into account this motion before sealing.
    Conversely, ceramic coving or quadrant ceramic tiles can be made use of to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and reduce to size, are likewise easily offered on the marketplace. It is advisable to fit the tiles making use of water-resistant or water resistant glue and grout.

    How to Install or Replace a Bathtub


    Find Your Dimensions


    The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.



    After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?


    Disconnect the Water Supply and Drain Assembly


    Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.



    Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.



    Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.


    Cut Out the Old Tub


    After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.



    Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.



    Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.


    Install the New Tub


    Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.



    Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.



    Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.



    When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.


    Secure the Tub


    After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.



    Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.



    Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.



    Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.

    https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/


    How to Install a Bathtub Yourself

    Do you like more info about How to Install a Bathtub? Post feedback directly below. We will be interested to hear your insights about this blog post. We are looking forward that you visit us again in the future. Feel free to take a moment to distribute this blog post if you enjoyed reading it. Thank you for your time invested reading it.


    For quick fixes, call!

    Report this page